New 2025R Compact Utility Tractor

2 Family Tractors (25-32 HP)

 (10) Recommended by 80.0%

Starting at: $16,669.00 USD

Key Features
  • Powerful and fuel-efficient Tier IV Yanmar engine
  • Hydro transmission with TwinTouch™ pedals for ease of use
  • AutoConnect™ 7-Iron Drive-over mower decks up to 60 inches
  • Standard cruise control, 12-V outlet and premium seating

More Info


Durable, efficient, high-torque 3-cylinder diesel engine provides adequate power
3-cylinder Yanmar TNV Series diesel engine3-cylinder Yanmar TNV Series diesel engine

Power is provided by a durable and efficient high-torque three-cylinder Yanmar® TNV Series diesel engine.


This series of engines was developed to meet Tier 4 Environmental Protection Agency (EPA) environmental requirements by featuring low levels of both exhaust and emissions.


Number of


Gross engine hp

Power take-off
(PTO) hp



1.267 L



Yanmar TNV Series engine offers these features:
  • Economical for good cooling and long life
  • Isolated engine provides reduced vibration and noise for the operator; indirect fuel injection uses a precombustion chamber to give the engine a smooth and quiet operation; aluminum-alloy piston with built-in steel struts are lightweight to reduce connection rod bearing loads and provide good heat transfer characteristics
    • Design permits tighter tolerances and neutralizes expansion of the piston, thereby reducing blow-by gas and less noise from the piston slap
    • Higher top rings on the piston and a thinner head gasket greatly reduces the volume of unburned waste gases and increases combustion efficiency
  • Timing-gear teeth have a designed roll-off profile giving almost no clash,no noise, and no backlash
  • High-torque reserve provides plenty of power under heavy load, yet retains excellent fuel economy
  • Easy access to engine check and fill points on the right-hand side of the tractor by removing the side panels
  • Fuel filter with replaceable element
  • Full-pressure lubrication system provides filtered oil under pressure to all vital engine parts
  • Glow plugs provide quick starts in temperatures down to 18°C (0°F) (Optional engine coolant heater attachment will assist starting under more extreme conditions.)
  • Auto-bleed fuel system means there is no special bleeding required if the tractor runs out of fuel; this system will self-prime the injection pump, lines, and injectors, providing fast fuel recovery
  • Key start and shut off eliminates fuel shut-off knob
  • Electric solenoid shuts fuel supply off immediately when key is turned off
  • See-through coolant recovery tank permits operator to check coolant level without removing radiator cap
  • Dry-type air cleaner with safety element keeps dirt and other contaminants out of the engine
    • Safety element (second filter) will protect engine if primary filter would develop a leak
    • Protects engine when servicing primary filter
  • Air filter restriction indicator is standard equipment on the 2025R Tractor
  • Sealed-radiator compartment keeps trash and debris on outside of hood
  • Horizontal exhaust discharges fumes away from the operator station, reducing noise and improving operator visibility and comfort

Yanmar is a trademark of Yanmar Company Limited.

Factory-installed mechanical mower deck lift components reduces dealer initial mower deck install
2025R Tractor2025R Tractor
  • The 2025R model includes factory-installed mechanical deck lift components.
  • The addition of these components from the factory significantly reduces the time required to do the initial mower deck installation at the time of purchase.
  • Refer to the mowers and material collection page for more details on mower deck installation and compatibility.
Optional iMatch™ Quick-Hitch feature allows for easy implement hookup
iMatch Quick-HitchiMatch Quick-Hitch
iMatch Quick-Hitch with rotary cutter hookupiMatch Quick-Hitch with rotary cutter hookup
iMatch Quick-Hitch (LVB25976)iMatch Quick-Hitch (LVB25976)
iMatch Quick-Hitch with rotary cutter hookup (LVB25976)iMatch Quick-Hitch with rotary cutter hookup (LVB25976)

One of the greatest operator concerns involves difficulty in attaching tractor implements. John Deere has addressed this issue with the iMatch Quick-Hitch.

The iMatch Quick-Hitch provides easy hookup and a guaranteed fit for all Category 1 implements that are designed to meet the ASABE Category 1 Standard S278.6 for quick-attach hitches.

  • All implements require a set of bushings in order for the attachment to fit and work properly with the iMatch Quick-Hitch. One set of bushings comes with the iMatch Quick-Hitch.

NOTE: The bushing set can be seen in the picture above. These bushings allow the hooks on the iMatch and the pins on the implement to fit together properly. All other implements (box blades, tillers, rear blades, etc.) will require a set of bushings to enlarge the pin to fit with the iMatch hooks. Bushings of different lengths can be found in the parts system or through a bushing supplier (see dimensions below).

  • Upper bushing
    • Inside diameter: 1.93-1.95 cm (0.76-0.77 in.)
    • Outside diameter: 3.15-3.18 cm (1.24-1.25 in.)
  • Lower bushings
    • Inside diameter: 2.24-2.26 cm (0.88 to 0.89 in.)
    • Outside diameter: 3.63-3.66 cm (1.43 to 1.44 in.)
Superb serviceability improves productivity

Regular service and maintenance are essential to the performance, productivity, and longevity of the tractor.

  • Two quarter-turn fasteners allow operators to easily remove the engine side panels without tools to access to the engine compartment
  • The under-hood gas-lift support provides easy access to the engine compartment and eliminates the need for a mechanical prop rod
  • External hood latch requires no tools and can release using the tractor key
  • Easy access to regular service points minimizes service time
  • Daily service checks, such as checking the engine oil or water separator, can be done without opening the hood or removing the tractor side panels
  • Tractors are equipped with a mechanical air filter restriction indicator that alerts the operator when the air filter needs to be cleaned or changed
  • All external engine, fuel and transmission filters are easily accessible
  • Fuel tank is located on the rear of the tractor to allow for easy access when fueling

NOTE:  Always refer to the operator’s manual for complete maintenance and service recommendations.

Implement compounding improves efficiency
Implement compounding (2025R Tractor shown)Implement compounding (2025R Tractor shown)
  • Loader, mid-mower, and a variety of rear hitch implements can be attached to the tractor at the same time
  • Optional premium independent mid lift system operates independent of the rear 3-point hitch. This gives the operator the flexibility to leave the mid mower attached when completing other tasks.

Premium independent mower lift system allows quick and easy adjustment

The optional premium independent lift system has been improved over the current 1 Family system by now allowing the operator to have full control of the mower deck in both the raise and lower positions. When the operator reaches the desired height, the button can be released and the deck will hold its position. This feature reduces the effort required to adjust the height-of-cut (HOC) dial and it also allows for quick height changes on the go.

Easy-to-use hydrostatic transmission (HST) increases efficiency

The 2R Series are equipped with a two-range hydrostatic transmission (HST) incorporated in a die-cast aluminum transmission case. Fluid under pressure transmits engine power to the drive wheels via a closed-loop pump and motor arrangement. Infinite ground speeds allow the operator to match the speed of the tractor to the job.

  • No clutching for fast and easy direction changes
  • Twin Touch™ foot pedals for quick and easy forward/reverse operation
  • Transmission oil cooler cools transmission oil for longer transmission life

Safety features of the HST include:

  • The tractor will only start with the range lever in neutral
    • If the range lever is in gear when the key is turned to the start position, the instrument panel instructs the operator to shift to neutral
  • The engine will shut off if the operator leaves the seat and the forward/reverse pedals are depressed
Twin Touch foot controls Twin Touch foot controls
Two-range transmission
Two-speed transmissionTwo-speed transmission

Transmission has two speeds - hi and lo range.

  • The range lever is located next to the seat, conveniently within reach of the operator
  • All tasks can be performed using two ranges on the 2025R which means less shifting throughout the day

Durability features include:

  1. Large forged one-piece trunnion shaft with larger support bearings that reduce vibration and noise
  2. Innovative transaxle combines an HST, gear reduction axle, and clutch
  3. Pressure side filtration allows the use of a fine-mesh filter
  4. One pump to supply charge pressure and implement A flow divider splits the flow to various circuits throughout the tractor.
  5. The transaxle has an oil cooler which provides improved hydraulic cooling performance
Open operator's station is comfortable and convenient
Open operator's stationOpen operator's station

The operator’s station has been designed to allow for greater operator comfort and increased visibility. The ergonomic layout and convenient color coded controls with large labels allow for easy identification and operation. Large and easy to grab handrails are located on each fender for an easier on and off of the tractor from either side.


Below are other key features of the 2025R Tractor operator’s station:       

  • Sloping hood design provides improved visibility
  • Plenty of room for comfortable operation
  • Cup holder, multiple storage compartments, and a 12-V outlet ensures an organized operator’s station
  • Fender-mounted handrails are large and easy to grab, assist the operator in getting on and off the tractor
  • Rubberized floor mat design to reduce vibration and noise
  • Step-through operator platform makes getting on and off the tractor easy
  • Front-horizontal exhaust for increased operator visibility
  • Controls have been raised and integrated into the fender for operator comfort and ease of use
  • Large, easy-to-read decals provide clear instructions for experienced and even non-experienced operators
  • Portable toolbox integrated into the front frame of the tractor
  • Fuel tank is located on the rear of the tractor to allow for easy access when fueling
Left-side step
  • The left-side step allows for easy access on and off the tractor
  • Foot platform has non-skid surface
Premium seat

The thick, soft padding on this seat provides a smooth and comfortable ride. A high, scalloped back makes it easier for the operator to turn to view rear implements.

  • Seat adjusts fore/aft for operator convenience
  • Seat flips forward for protection from the elements
  • High seat back and armrests are in base equipment and allow for a more comfortable operation
  • Retractable seat belt feature prevents the seat belt from becoming tangled in the seat suspension and controls

Key features of the operator’s station include:

  • Tilt steering wheel design in base equipment on the 2025R Tractor
  • Allows the operator to adjust the steering wheel to the most comfortable position
  • Provides additional clearance for the operator to enter and exit the tractor
  • Provides easy return to the fully raised position
  • Provides plenty of room for comfortable operation
  • Easy-fold rollover protective structure (ROPS) allows the tractor to be used or stored in low-clearance environments
Standard lighting shownStandard lighting shown
Optional premium lighting shownOptional premium lighting shown

Standard equipment lighting includes:

  • Two front-mounted sealed-beam halogen headlights
  • Two amber-flashing warning/hazard lights mounted on the side of the rollover protective structure (ROPS) with reflectors
  • Two additional fender lights are standard on the 2025R
  • Additional front- and rear-light kits are available

For those operators requiring additional lighting, additional light options are available:

  • Premium light kit
    • Two light-emitting diode (LED) fender lights
    • Two LED ROPS work lights (adjustable 360 degrees for forward or rear lighting)
    • One LED rear PTO light
  • Auxiliary rear work light
    • One halogen light
  • Forward halogen work light kit
    • Contains two ROPS mounted lights
  • Forward LED work light kit
    • Contains two ROPS mounted lights

NOTE: Lights mounted to the ROPS will require the warning light brush guard kit.


Optional work light brush guards can ordered to protect lights from debris.

Fast and easy implement changeover offers versatility
  • Front Quik-Tatch™ hitch makes changing front implements quick and easy
  • All front implements (blades, brooms, and snow blowers) use a common hitch
  • AutoConnect™ Mid-Mount Mower Deck, 120R Loader, and 260B Backhoe can be taken on or off within 5 minutes, and no tools are required
  • Changing rear implements is a snap with the iMatch™ Quick-Hitch, which has three fixed points to back in and pick up a rear implement that is iMatch™ compatible


Key Specs
Engine power (gross) 17.8 kW
23.9 hp
SAE J1995 rated power
Power take-off (PTO) power 13.4 kW
18 hp
Steering hydraulics 13.25 L/min
3.5 gpm
Implement hydraulics 13.25 L/min
3.5 gpm
Hitch type Limited Category 1
Lift capacity, 24-in. behind link arms 400 kg
882 lb
Standard transmission; forward/reverse Hydrostatic - 2 range
Cruise control Standard
Approximate shipping weight (open-station; cab) 813.5 kg
1793.4 lb
Wheelbase 1600 mm
63 in.
Family GYDXL1.27NS1
Manufacturer Yanmar
Engine model 3TNV80F-NCJT
Engine power (gross) 17.8 kW
23.9 hp
SAE J1995 rated power
Power take-off (PTO) power 13.4 kW
18 hp
Rated engine speed 3200 rpm
Type Diesel
Injection pump type Indirect injection
Aspiration Natural
Emissions compliance Final Tier 4
Cylinders/displacement 3 / 1.267 L
3 / 77 cu in.
Number of cylinders Three
Cylinder liners Cast-in-block
Bore and stroke 80 x 84 mm
3.2 x 3.3 in.
Compression ratio 23:01
Lubrication Pressurized
Cooling system Water pump
Air cleaner Dual element
Engine torque at rated speed 53 Nm
39.09 lb-ft
Fuel tank capacity 23.8 L
6.3 gal.
Battery size 500 CCA
Alternator (12-V) 40 amp
Starter size 1.2 kW
1.6 hp
Fuel system
Type Indirect injection
Fuel consumption
5.8 L/hr
1.5 U.S. gal./hr
Standard transmission; forward/reverse Hydrostatic - 2 range
Optional transmission; forward/reverse
Left-hand reverser No
Transmission gear ranges
Final drive Spur Gear
Brakes Wet disc
Steering Power steering
Clutch, wet/dry
Clutch disk diameter wet clutch
Axle capacity Front
612 kg
1349 lb
1100 kg
2425 lb
Creeper No
Cruise control Standard
Differential lock Yes
Drawbar maximum vertical load
Type Open center
Pump rated output Steering
13.25 L/min
3.5 gpm
13.25 L/min
3.5 gpm
26.5 L/min
7.0 gpm
Pump type Gear
Maximum operating pressure 148.2 bar
2150 psi
Draft control sensing Position control
Remote control valves available Two
3-point hitch
Type Limited Category 1
Lift capacity, 24-in. behind link arms 400 kg
882 lb
Power take-off (PTO)
Standard Rear - 540 rpm
Mid - 2100 rpm
Control Independent
Clutch Wet disc
Brake (for mid and rear PTO) Wet disc
Engagement method
Fluid capacities
Crankcase with filter 2.7 L
2.9 qt
Transmission and hydraulic system
Final drive
Type Spur Gear
Differential lock Yes
Operator station
Rollover protective structure Type
Platform - flat/straddle Three-piece semi flat
Gear shift location - console/floor Left-hand side
Air conditioning, temperature differential
Noise rating
Seat equipment
Wheelbase 1600 mm
63 in.
Front axle clearance 316 mm
12.5 in.
Turning radius with brakes
Turning radius without brakes 2.65 m
8.7 ft
Limited slip differential No
Approximate shipping weight (open-station; cab) 813.5 kg
1793.4 lb
Front R3 Turf - 23x8.50-12
R4 Industrial - 23x8.50-12
R3 Radial - 220/55-R12
Rear R3 Turf - 31x13.5-15
R4 Industrial - 12-16.5
R3 Radial - 280/70-R16
Front tread range 95.3 cm
37.5 in.
Rear tread spacing
Toolbox Yes
Tilt steering wheel Yes
12-V Outlet Yes

Accessories and Attachments

Ballast Box

Ballast Box - BW15073
Ballast Box Extension - BW15074

Cab Operator's Station

Beacon Light Kit - LP70012
Drop-on cab from Mauser (Heat Only) - LP70009
Illuminated Rear License Plate Kit - LP70014
Rear LED Work Light Kit - LP70013
Rear Wiper Kit - LP70011
Stereo Kit - LP70016

Cold Start Packages

Engine Block Heater Adapter - AM134805


Auto-Throttle Kit - BLV10784
Engine Coolant Heater Kit (110 Volt) - BLV10640

Front Fenders

Turnable Front Fender Kit with Quick Release Mechanism - BLV10945

Front Power Take-Off (PTO)

2000 RPM Front PTO - BLV10681

Front Quick-Hitch

Quick Hitch Kit (1023E, 1025R, 1026R, model year 2017- 2025R, 2026R) - BLV10708

Front Wheels and Tires

220/55-12 (R3 Turf) Radial Front Wheels & Tires - BLV10745
23x8.5-12 (R3 Turf) Bias Ply Front Wheels & Tires - BLV10741
23x8.5-12 (R4 Industrial) Bias Ply Front Wheels & Tires - BLV10743

Hitch Type

iMatch Bushing Kit - LP19969
iMatch Bushing Kit - LP25004
iMatch Quick Hitch Upper Adapter Bushing - PM00353
iMatch Quick Hitch Upper Adapter Bushing - PM03008

Hydraulic Angling

Hydraulic angling (1023E, 1025R, 1026R, model year 2017- 2025R, 2026R) - BLV10880


Power Beyond Kit - BLV10746
Rear Hydraulic Outlet Kit - BLV10775
Rear Third Selective Control Valve Kit Without Detent - BLV11025


Premium LED Work Light Kit - BLV10673

Lighting Equipment

Auxiliary Rear Work Light Kit (1 Light) - LVB25547
Forward Lighting Kit (2 Lights) - LVB25546
LED Work Light Kit - BLV10497
Warning Light Brush Guard Kit (Two Guards) - BLV10400
Work Light Brush Guard Kit (OOS Only) - BLV10399


3-Point Hitch Tractor Receiver Hitch - LP25001
55-amp alternator - LVB25015
Attaching Hardware for Rear Wheel Weight, 60 lb - BM17987
Canopy Kit - Rigid Plastic - LP64809
Front Attaching Support kit (model year 2017- 2025R, 2026R) - BLV10680
Front Weight Bracket Extension Kit (1023E, 1025R, 1026R, 2305, 2025R, 2026R, 2320, 2520) - BLV10623
Rear License Plate Kit (Includes Light) - BLV11042
Seat Cover - LP68694
Spark Arrester Screen for Muffler - LVA15392
Tire Chains - TY15201
Tractor Cover - LP95637
iMatch Quick Hitch Bushings - LVU15507
iMatch/Quik-Coupler Brushing Kit - BW15056

Rear Fenders

Rear FenderExtension Kit - BLV10930

Rear Hitch

iMatch Quick Hitch Bushings - LVU12858
iMatch Quick-Hitch Category 1 with adjustable top hook - LVB25976

Rear Wheels and Tires

12-16.5 (R3 Turf) Bias Ply Rear Wheels & Tires - BLV10740
12x16.5 (R4 Industrial) Bias Ply Rear Wheels & Tires - BLV10742
280/70-16 (R3 Turf) Radial Rear Wheels & Tires - BLV10744


Quik-Tatch Weight, 42 lb (19 kg) - UC13263
Rear Wheel Weight, 60 lb (27.2 kg) - BM17965